gTrack
PlatformLive GPS trackingTrip history & playbackAlerts & event rulesReportsGeofencesFuel & sensorsDrivers & behaviourFleet maintenanceVideo telematicsRemote commandsMobile appAI gTrack assistantAPI & integrations
SolutionsTransport & logisticsDelivery & courierConstruction & machineryTaxi & passenger transportCorporate fleetsCar rentalCold chainPublic sector & utilities
DevicesPricing
ResourcesGetting startedFAQSecurity & privacyPartners & resellers
CompanyAbout gTrackContact & quotePrivacy policyTerms of service
Request a quote
Concox / Jimi IoT connection guide

Concox JM-VL502 GPS tracking setup

Connect your Concox JM-VL502 to gTrack on the JT/T 808 (jt808) protocol. This page lists its server settings and what gTrack reads from it. gTrack provides tracking software and does not sell trackers.

About this model

About the JM-VL502

The JM-VL502 is a Jimi IoT vehicle tracker on JT/T 808.

Connection settings

Concox JM-VL502 server and port

Tracker modelConcox JM-VL502
Server / hostnametracker.uplisoft.com
Port5015
TransportTCP
ProtocolJT/T 808 (jt808)

Enter the hostname without https:// and keep the port in its separate setting. Select TCP in your tracker configuration. Use the APN supplied by your SIM provider and check that mobile data is available.

Data in gTrack

What gTrack reads from the JM-VL502

  • Jimi IoT alarms and events, each by name, with the driver card ID on login and logout
  • Status: charging, battery level and voltage, external voltage, GSM signal, sleep state
  • Bluetooth sensors: temperature, humidity, door and light, fuel level probes
  • Fuel level sensors (ultrasonic and capacitive) and remote fuel / power cut
Setup

Add Concox JM-VL502 to your fleet

  1. Add the vehicle

    In gTrack click + Asset, give it a name and choose the tracker model.

  2. Enter the identifier

    Use the IMEI or device identifier printed on your tracker. Add its SIM phone number and APN in the tracker form.

  3. Set the server

    Configure your tracker to send to tracker.uplisoft.com using the model’s port and TCP or UDP transport shown below.

  4. Drive

    The first position appears as soon as the tracker connects — usually within minutes.

In the tracker form, choose Concox JM-VL502 and enter the identifier exactly as shown on your device. Saving these fields does not remotely reconfigure the tracker: apply the server settings using its manufacturer’s configuration tool or supported SMS commands.

Check the connection

From the first packet to the live map

Open the device Terminal in gTrack to check incoming packets and decoded reports. Confirm the identifier, APN, hostname, port and transport if the device remains offline. A device without a GPS fix may connect before it can show a valid position.

Once Concox JM-VL502 sends valid data, use gTrack for live location, trip history, geofences and alerts. Fuel, ignition, temperature and other sensor values depend on the device, its wiring and firmware configuration.

Compare other Concox / Jimi IoT models or read the platform setup guide.

Similar models

Other Concox / Jimi IoT models on JT/T 808 (jt808)

Concox JC181 · Concox JC182 · Concox JC270 · Concox JC371 · Concox JC450 · Concox JC450PRO · Concox JC451 · Concox JM-VL533

FAQ

Questions and answers

Which server and port does the JM-VL502 use with gTrack?

Server tracker.uplisoft.com, port 5015, TCP, JT/T 808 (jt808) protocol.

Do I need to buy the JM-VL502 from gTrack?

No. gTrack is tracking software: connect the JM-VL502 you already have.