gTrack
PlatformLive GPS trackingTrip history & playbackAlerts & event rulesReportsGeofencesFuel & sensorsDrivers & behaviourFleet maintenanceVideo telematicsRemote commandsMobile appAI gTrack assistantAPI & integrations
SolutionsTransport & logisticsDelivery & courierConstruction & machineryTaxi & passenger transportCorporate fleetsCar rentalCold chainPublic sector & utilities
DevicesPricing
ResourcesGetting startedFAQSecurity & privacyPartners & resellers
CompanyAbout gTrackContact & quotePrivacy policyTerms of service
Request a quote
Concox / Jimi IoT connection guide

Concox JC371 GPS tracking setup

Connect your Concox JC371 to gTrack on the JT/T 808 (jt808) protocol (video over JT/T 1078 (jt1078)). This page lists its server settings and what gTrack reads from it. gTrack provides tracking software and does not sell trackers.

About this model

About the JC371

The JC371 is a Jimi IoT dashcam on JT/T 808, with video over JT/T 1078.

Connection settings

Concox JC371 server and port

Tracker modelConcox JC371
Server / hostnametracker.uplisoft.com
Port5015
TransportTCP
ProtocolJT/T 808 (jt808)
Video (live and playback)JT/T 1078 (jt1078), port 5263, TCP

Enter the hostname without https:// and keep the port in its separate setting. Select TCP in your tracker configuration. Use the APN supplied by your SIM provider and check that mobile data is available.

Data in gTrack

What gTrack reads from the JC371

  • ADAS alerts: forward collision, lane departure, headway and pedestrian warnings (9 types)
  • DMS alerts: fatigue, phone use, smoking, distraction, seat belt and more (13 types)
  • Jimi IoT extended alarms: 62 camera, driving and basic alarm codes, each by name
  • Live video over JT/T 1078 (port 5263) and the photos the camera takes on an event or on request
  • Status: ignition, battery and external voltage, GSM signal, satellites, fuel and temperature sensors
Setup

Add Concox JC371 to your fleet

  1. Add the vehicle

    In gTrack click + Asset, give it a name and choose the tracker model.

  2. Enter the identifier

    Use the IMEI or device identifier printed on your tracker. Add its SIM phone number and APN in the tracker form.

  3. Set the server

    Configure your tracker to send to tracker.uplisoft.com using the model’s port and TCP or UDP transport shown below.

  4. Drive

    The first position appears as soon as the tracker connects — usually within minutes.

In the tracker form, choose Concox JC371 and enter the identifier exactly as shown on your device. Saving these fields does not remotely reconfigure the tracker: apply the server settings using its manufacturer’s configuration tool or supported SMS commands.

Check the connection

From the first packet to the live map

Open the device Terminal in gTrack to check incoming packets and decoded reports. Confirm the identifier, APN, hostname, port and transport if the device remains offline. A device without a GPS fix may connect before it can show a valid position.

Once Concox JC371 sends valid data, use gTrack for live location, trip history, geofences and alerts. Fuel, ignition, temperature and other sensor values depend on the device, its wiring and firmware configuration.

Compare other Concox / Jimi IoT models or read the platform setup guide.

Similar models

Other Concox / Jimi IoT models on JT/T 808 (jt808)

Concox JC181 · Concox JC182 · Concox JC270 · Concox JC450 · Concox JC450PRO · Concox JC451 · Concox JM-VL502 · Concox JM-VL533

FAQ

Questions and answers

Which server and port does the JC371 use with gTrack?

Server tracker.uplisoft.com, port 5015, TCP, JT/T 808 (jt808) protocol. Video goes to port 5263 over JT/T 1078 (jt1078).

Does gTrack show the JC371's ADAS and DMS alerts?

Yes. Every ADAS and DMS alert type and every Jimi IoT alarm code is shown by its name, with live video and the alarm photos.

Do I need to buy the JC371 from gTrack?

No. gTrack is tracking software: connect the JC371 you already have.