gTrack
PlatformLive GPS trackingTrip history & playbackAlerts & event rulesReportsGeofencesFuel & sensorsDrivers & behaviourFleet maintenanceVideo telematicsRemote commandsMobile appAI gTrack assistantAPI & integrations
SolutionsTransport & logisticsDelivery & courierConstruction & machineryTaxi & passenger transportCorporate fleetsCar rentalCold chainPublic sector & utilities
DevicesPricing
ResourcesGetting startedFAQSecurity & privacyPartners & resellers
CompanyAbout gTrackContact & quotePrivacy policyTerms of service
Request a quote
Teltonika connection guide

Teltonika FMU125 GPS tracking setup

Connect your Teltonika FMU125, an advanced vehicle tracker with extra inputs and outputs, to gTrack on the teltonika protocol. This page lists its server settings, the SMS command and what gTrack reads from it. gTrack provides tracking software and does not sell trackers.

About this model

About the FMU125

The FMU125 is an advanced vehicle tracker with extra inputs and outputs by Teltonika.

Connection settings

Teltonika FMU125 server and port

Tracker modelTeltonika FMU125
Server / hostnametracker.uplisoft.com
Port11445
TransportTCP / UDP
Protocolteltonika

Enter the hostname without https:// and keep the port in its separate setting. Choose TCP or UDP to match your device configuration. Use the APN supplied by your SIM provider and check that mobile data is available.

Configure the tracker

Set the FMU125 to send to gTrack

  1. Open Teltonika Configurator and connect the FMU125 with a USB cable or Bluetooth.
  2. In GPRS, set the APN of your SIM card.
  3. Under Server settings: Domain tracker.uplisoft.com, Port 11445, Protocol TCP.
  4. Save the configuration to the device. The first position arrives within a few minutes.

Or by SMS. Send this to the tracker's phone number, with two spaces first when its SMS login and password are empty, and your APN in place of <APN>:

  setparam 2001:<APN>;2004:tracker.uplisoft.com;2005:11445;2006:0
Setup

Add Teltonika FMU125 to your fleet

  1. Add the vehicle

    In gTrack click + Asset, give it a name and choose the tracker model.

  2. Enter the identifier

    Use the IMEI or device identifier printed on your tracker. Add its SIM phone number and APN in the tracker form.

  3. Set the server

    Configure your tracker to send to tracker.uplisoft.com using the model’s port and TCP or UDP transport shown below.

  4. Drive

    The first position appears as soon as the tracker connects — usually within minutes.

In the tracker form, choose Teltonika FMU125 and enter the identifier exactly as shown on your device. Saving these fields does not remotely reconfigure the tracker: apply the server settings using its manufacturer’s configuration tool or supported SMS commands.

Check the connection

From the first packet to the live map

Open the device Terminal in gTrack to check incoming packets and decoded reports. Confirm the identifier, APN, hostname, port and transport if the device remains offline. A device without a GPS fix may connect before it can show a valid position.

Once Teltonika FMU125 sends valid data, use gTrack for live location, trip history, geofences and alerts. Fuel, ignition, temperature and other sensor values depend on the device, its wiring and firmware configuration.

Compare other Teltonika models or read the platform setup guide.

FAQ

Questions and answers

Which server and port does the FMU125 use with gTrack?

Server tracker.uplisoft.com, port 11445, TCP / UDP, teltonika protocol.

Can I set the FMU125 by SMS?

Yes. Send "setparam 2001:<APN>;2004:tracker.uplisoft.com;2005:11445;2006:0" to the tracker, with two spaces before it when the SMS login and password are empty, and your APN in place of <APN>.

Do I need to buy the FMU125 from gTrack?

No. gTrack is tracking software: connect the FMU125 you already have.