gTrack
PlatformLive GPS trackingTrip history & playbackAlerts & event rulesReportsGeofencesFuel & sensorsDrivers & behaviourFleet maintenanceVideo telematicsRemote commandsMobile appAI gTrack assistantAPI & integrations
SolutionsTransport & logisticsDelivery & courierConstruction & machineryTaxi & passenger transportCorporate fleetsCar rentalCold chainPublic sector & utilities
DevicesPricing
ResourcesGetting startedFAQSecurity & privacyPartners & resellers
CompanyAbout gTrackContact & quotePrivacy policyTerms of service
Request a quote
Concox / Jimi IoT connection guide

JIMI JM0X models GPS tracking setup

Connect your JIMI JM0X models to gTrack on the gt06 protocol. This page lists its server settings, the SMS command and what gTrack reads from it. gTrack provides tracking software and does not sell trackers.

About this model

About the JM0X models

The JM0X models is a Concox / Jimi IoT tracker on the GT06 protocol.

Connection settings

JIMI JM0X models server and port

Tracker modelJIMI JM0X models
Server / hostnametracker.uplisoft.com
Port5023
TransportTCP
Protocolgt06

Enter the hostname without https:// and keep the port in its separate setting. Select TCP in your tracker configuration. Use the APN supplied by your SIM provider and check that mobile data is available.

Configure the tracker

Set the JM0X models to send to gTrack

Send these two SMS commands to the tracker's phone number, your APN in place of <APN>. The tracker answers each one with a confirmation.

APN,<APN>#
SERVER,1,tracker.uplisoft.com,5023,0#

Some firmware versions use a different command format: check the manual of your model if the tracker does not confirm.

Data in gTrack

What gTrack reads from the JM0X models

  • All 173 Jimi IoT alarm and event codes, each by name: SOS, tow, wire cut, door, airbag, rollover, jamming and more
  • Status: ignition, external and battery voltage, battery level, GSM signal, satellites
  • Driving: harsh acceleration, braking and cornering, collision, overspeed
Setup

Add JIMI JM0X models to your fleet

  1. Add the vehicle

    In gTrack click + Asset, give it a name and choose the tracker model.

  2. Enter the identifier

    Use the IMEI or device identifier printed on your tracker. Add its SIM phone number and APN in the tracker form.

  3. Set the server

    Configure your tracker to send to tracker.uplisoft.com using the model’s port and TCP or UDP transport shown below.

  4. Drive

    The first position appears as soon as the tracker connects — usually within minutes.

In the tracker form, choose JIMI JM0X models and enter the identifier exactly as shown on your device. Saving these fields does not remotely reconfigure the tracker: apply the server settings using its manufacturer’s configuration tool or supported SMS commands.

Check the connection

From the first packet to the live map

Open the device Terminal in gTrack to check incoming packets and decoded reports. Confirm the identifier, APN, hostname, port and transport if the device remains offline. A device without a GPS fix may connect before it can show a valid position.

Once JIMI JM0X models sends valid data, use gTrack for live location, trip history, geofences and alerts. Fuel, ignition, temperature and other sensor values depend on the device, its wiring and firmware configuration.

Compare other Concox / Jimi IoT models or read the platform setup guide.

Similar models

Other Concox / Jimi IoT models on gt06

Concox AT3 · Concox AT4 · Concox CRX1 · Concox CT10 · Concox GK301 · Concox GK309 · Concox GS503 · Concox GT02

FAQ

Questions and answers

Which server and port does the JM0X models use with gTrack?

Server tracker.uplisoft.com, port 5023, TCP, gt06 protocol.

Which SMS sets the JM0X models to gTrack?

APN,<APN># with your APN, then SERVER,1,tracker.uplisoft.com,5023,0#

Does gTrack show the JM0X models's alarms?

Yes, all 173 alarm and event codes of Jimi IoT's documentation, each by name, ready for rules and notifications.

Do I need to buy the JM0X models from gTrack?

No. gTrack is tracking software: connect the JM0X models you already have.