gTrack
PlatformLive GPS trackingTrip history & playbackAlerts & event rulesReportsGeofencesFuel & sensorsDrivers & behaviourFleet maintenanceVideo telematicsRemote commandsMobile appAI gTrack assistantAPI & integrations
SolutionsTransport & logisticsDelivery & courierConstruction & machineryTaxi & passenger transportCorporate fleetsCar rentalCold chainPublic sector & utilities
DevicesPricing
ResourcesGetting startedFAQSecurity & privacyPartners & resellers
CompanyAbout gTrackContact & quotePrivacy policyTerms of service
Request a quote
Concox / Jimi IoT connection guide

Concox GK503 GPS tracking setup

Connect your Concox GK503 to gTrack on the gt06 protocol. This page lists its server settings, the SMS command and what gTrack reads from it. gTrack provides tracking software and does not sell trackers.

About this model

About the GK503

The GK503 is a Concox / Jimi IoT tracker on the GT06 protocol.

Connection settings

Concox GK503 server and port

Tracker modelConcox GK503
Server / hostnametracker.uplisoft.com
Port5023
TransportTCP
Protocolgt06

Enter the hostname without https:// and keep the port in its separate setting. Select TCP in your tracker configuration. Use the APN supplied by your SIM provider and check that mobile data is available.

Configure the tracker

Set the GK503 to send to gTrack

Send these two SMS commands to the tracker's phone number, your APN in place of <APN>. The tracker answers each one with a confirmation.

APN,<APN>#
SERVER,1,tracker.uplisoft.com,5023,0#

Some firmware versions use a different command format: check the manual of your model if the tracker does not confirm.

Data in gTrack

What gTrack reads from the GK503

  • All 173 Jimi IoT alarm and event codes, each by name: SOS, tow, wire cut, door, airbag, rollover, jamming and more
  • Status: ignition, external and battery voltage, battery level, GSM signal, satellites
  • Driving: harsh acceleration, braking and cornering, collision, overspeed
Setup

Add Concox GK503 to your fleet

  1. Add the vehicle

    In gTrack click + Asset, give it a name and choose the tracker model.

  2. Enter the identifier

    Use the IMEI or device identifier printed on your tracker. Add its SIM phone number and APN in the tracker form.

  3. Set the server

    Configure your tracker to send to tracker.uplisoft.com using the model’s port and TCP or UDP transport shown below.

  4. Drive

    The first position appears as soon as the tracker connects — usually within minutes.

In the tracker form, choose Concox GK503 and enter the identifier exactly as shown on your device. Saving these fields does not remotely reconfigure the tracker: apply the server settings using its manufacturer’s configuration tool or supported SMS commands.

Check the connection

From the first packet to the live map

Open the device Terminal in gTrack to check incoming packets and decoded reports. Confirm the identifier, APN, hostname, port and transport if the device remains offline. A device without a GPS fix may connect before it can show a valid position.

Once Concox GK503 sends valid data, use gTrack for live location, trip history, geofences and alerts. Fuel, ignition, temperature and other sensor values depend on the device, its wiring and firmware configuration.

Compare other Concox / Jimi IoT models or read the platform setup guide.

Similar models

Other Concox / Jimi IoT models on gt06

Concox AT3 · Concox AT4 · Concox CRX1 · Concox CT10 · Concox GK301 · Concox GK309 · Concox GS503 · Concox GT02

FAQ

Questions and answers

Which server and port does the GK503 use with gTrack?

Server tracker.uplisoft.com, port 5023, TCP, gt06 protocol.

Which SMS sets the GK503 to gTrack?

APN,<APN># with your APN, then SERVER,1,tracker.uplisoft.com,5023,0#

Does gTrack show the GK503's alarms?

Yes, all 173 alarm and event codes of Jimi IoT's documentation, each by name, ready for rules and notifications.

Do I need to buy the GK503 from gTrack?

No. gTrack is tracking software: connect the GK503 you already have.