gTrack
PlatformLive GPS trackingTrip history & playbackAlerts & event rulesReportsGeofencesFuel & sensorsDrivers & behaviourFleet maintenanceVideo telematicsRemote commandsMobile appAI gTrack assistantAPI & integrations
SolutionsTransport & logisticsDelivery & courierConstruction & machineryTaxi & passenger transportCorporate fleetsCar rentalCold chainPublic sector & utilities
DevicesPricing
ResourcesGetting startedFAQSecurity & privacyPartners & resellers
CompanyAbout gTrackContact & quotePrivacy policyTerms of service
Request a quote
Teltonika connection guide

Teltonika FMB630 GPS tracking setup

Connect your Teltonika FMB630, a professional tracker for trucks and heavy machinery, to gTrack on the teltonika protocol. This page lists its server settings, the SMS command and what gTrack reads from it. gTrack provides tracking software and does not sell trackers.

About this model

About the FMB630

The FMB630 is a professional tracker for trucks and heavy machinery by Teltonika. gTrack reads 265 different values from it, listed below. Specifications, manuals and firmware: official FMB630 documentation.

Connection settings

Teltonika FMB630 server and port

Tracker modelTeltonika FMB630
Server / hostnametracker.uplisoft.com
Port11445
TransportTCP / UDP
Protocolteltonika

Enter the hostname without https:// and keep the port in its separate setting. Choose TCP or UDP to match your device configuration. Use the APN supplied by your SIM provider and check that mobile data is available.

Configure the tracker

Set the FMB630 to send to gTrack

  1. Open Teltonika Configurator and connect the FMB630 with a USB cable or Bluetooth.
  2. In GPRS, set the APN of your SIM card.
  3. Under Server settings: Domain tracker.uplisoft.com, Port 11445, Protocol TCP.
  4. Save the configuration to the device. The first position arrives within a few minutes.

Or by SMS. Send this to the tracker's phone number, with two spaces first when its SMS login and password are empty, and your APN in place of <APN>:

  setparam 2001:<APN>;2004:tracker.uplisoft.com;2005:11445;2006:0
Data in gTrack

What gTrack reads from the FMB630

265 values of the FMB630, ready for the live map, reports, rules and notifications.

  • Digital inputs (4): Digital Input 1, Digital Input 2, Digital Input 3, Digital Input 4
  • Digital outputs (4): Digital Output 3, Digital Output 4, Digital Output 1, Digital Output 2
  • Analog inputs (4): Analog Input 1, Analog Input 2, Analog Input 3, Analog Input 4
  • Vehicle CAN data (53): CAN300 Program Number, CAN300 Module ID, CAN300 Engine Work Time, CAN300 Engine Work Time Counted and more
  • 1-Wire temperature (12): Dallas Temperature ID 5, Dallas Temperature 5, Dallas Temperature ID 6, Dallas Temperature 6 and more
  • Fuel level sensors (3): LLSFuel Level 3, LLSFuel Level 4, LLSFuel Level 5
  • Tachograph (8): Tacho Data Source, Tachograph Performance, Tachograph Vehicle In Motion, Tachograph Overspeed and more
  • Driver identification (3): IButton Extended, RFID Extended, RFID COM2 Extended
  • Driving behaviour (6): Idling, Crash Detection, Geofence Zone Over Speeding, Green Driving Type and more
  • Power and battery (4): Power Supply Voltage, Battery Voltage, Battery Current, Battery Temperature
  • GNSS and GSM (6): Gsm Signal Strength, GNSSstatus, PDOP, HDOP and more
  • Other values (158)
Setup

Add Teltonika FMB630 to your fleet

  1. Add the vehicle

    In gTrack click + Asset, give it a name and choose the tracker model.

  2. Enter the identifier

    Use the IMEI or device identifier printed on your tracker. Add its SIM phone number and APN in the tracker form.

  3. Set the server

    Configure your tracker to send to tracker.uplisoft.com using the model’s port and TCP or UDP transport shown below.

  4. Drive

    The first position appears as soon as the tracker connects — usually within minutes.

In the tracker form, choose Teltonika FMB630 and enter the identifier exactly as shown on your device. Saving these fields does not remotely reconfigure the tracker: apply the server settings using its manufacturer’s configuration tool or supported SMS commands.

Check the connection

From the first packet to the live map

Open the device Terminal in gTrack to check incoming packets and decoded reports. Confirm the identifier, APN, hostname, port and transport if the device remains offline. A device without a GPS fix may connect before it can show a valid position.

Once Teltonika FMB630 sends valid data, use gTrack for live location, trip history, geofences and alerts. Fuel, ignition, temperature and other sensor values depend on the device, its wiring and firmware configuration.

Compare other Teltonika models or read the platform setup guide.

Similar models

Other Teltonika professional trackers

Teltonika FMB640 · Teltonika FMB641 · Teltonika FMC640 · Teltonika FMC650 · Teltonika FMM640 · Teltonika FMM650

FAQ

Questions and answers

Which server and port does the FMB630 use with gTrack?

Server tracker.uplisoft.com, port 11445, TCP / UDP, teltonika protocol.

Can I set the FMB630 by SMS?

Yes. Send "setparam 2001:<APN>;2004:tracker.uplisoft.com;2005:11445;2006:0" to the tracker, with two spaces before it when the SMS login and password are empty, and your APN in place of <APN>.

What data does gTrack read from the FMB630?

265 values: digital inputs, digital outputs, analog inputs, vehicle can data, 1-wire temperature, fuel level sensors, tachograph, driver identification, driving behaviour, power and battery, gnss and gsm.

Do I need to buy the FMB630 from gTrack?

No. gTrack is tracking software: connect the FMB630 you already have.