Teltonika FMB100 GPS tracking setup
Connect your Teltonika FMB100 to gTrack on the teltonika protocol. This page lists its server settings, the SMS command and what gTrack reads from it. gTrack provides tracking software and does not sell trackers.
Teltonika FMB100 server and port
| Tracker model | Teltonika FMB100 |
|---|---|
| Server / hostname | tracker.uplisoft.com |
| Port | 11445 |
| Transport | TCP / UDP |
| Protocol | teltonika |
Enter the hostname without https:// and keep the port in its separate setting. Choose TCP or UDP to match your device configuration. Use the APN supplied by your SIM provider and check that mobile data is available.
Set the FMB100 to send to gTrack
- Open Teltonika Configurator and connect the FMB100 with a USB cable or Bluetooth.
- In GPRS, set the APN of your SIM card.
- Under Server settings: Domain
tracker.uplisoft.com, Port11445, ProtocolTCP. - Save the configuration to the device. The first position arrives within a few minutes.
Or by SMS. Send this to the tracker's phone number, with two spaces first when its SMS login and password are empty, and your APN in place of <APN>:
setparam 2001:<APN>;2004:tracker.uplisoft.com;2005:11445;2006:0
What gTrack reads from the FMB100
248 values of the FMB100, ready for the live map, reports, rules and notifications.
- Digital inputs (4): Digital Input 1, Digital Input 2, Digital Input 3, DIN2 AIN2 Spec Event
- Digital outputs (2): Digital Output 1, Digital Output 2
- Analog inputs (2): Analog Input 2, Analog Input 1
- Vehicle CAN data (39): CAN300 Vehicle Speed, CAN300 Acc Pedal Position, CAN300 Fuel Consumed, CAN300 Fuel Level Liters and more
- OBD-II data (28): OBD Engine Load, OBD Engine Coolant Temperature, OBD Short Term Fuel Trim 1, OBD Fuel Pressure and more
- Bluetooth sensors (12): BLE Battery Voltage Percent 2, BLE Battery Voltage Percent 3, BLE Battery Voltage Percent 4, BLE Temperature Extended 1 and more
- 1-Wire temperature (8): Dallas Temperature ID 4, Dallas Temperature 1, Dallas Temperature 2, Dallas Temperature 3 and more
- Fuel level sensors (5): LLSFuel Level 1, LLSFuel Level 2, LLSFuel Level 3, LLSFuel Level 4 and more
- Tachograph (3): Tachograph Total Vehicle Distance, Tachograph Vehicle Speed, Tacho Driver Card Presence
- Driver identification (3): Authorized IButton, IButton Extended, RFID Extended
- Driving behaviour (10): Pulse Counter Din 1, Pulse Counter Din 2, Number Of Records, Eco Score and more
- Power and battery (5): External Voltage, Battery Voltage, Battery Current, Battery Temperature and more
- GNSS and GSM (9): ICCID1, Fuel Used GPS, ICCID2, Gsm Signal Strength and more
- Other values (118)
Add Teltonika FMB100 to your fleet
- Add the vehicle
In gTrack click + Asset, give it a name and choose the tracker model.
- Enter the identifier
Use the IMEI or device identifier printed on your tracker. Add its SIM phone number and APN in the tracker form.
- Set the server
Configure your tracker to send to tracker.uplisoft.com using the model’s port and TCP or UDP transport shown below.
- Drive
The first position appears as soon as the tracker connects — usually within minutes.
In the tracker form, choose Teltonika FMB100 and enter the identifier exactly as shown on your device. Saving these fields does not remotely reconfigure the tracker: apply the server settings using its manufacturer’s configuration tool or supported SMS commands.
From the first packet to the live map
Open the device Terminal in gTrack to check incoming packets and decoded reports. Confirm the identifier, APN, hostname, port and transport if the device remains offline. A device without a GPS fix may connect before it can show a valid position.
Once Teltonika FMB100 sends valid data, use gTrack for live location, trip history, geofences and alerts. Fuel, ignition, temperature and other sensor values depend on the device, its wiring and firmware configuration.
Compare other Teltonika models or read the platform setup guide.
Other Teltonika models on teltonika
Teltonika AT1000 · Teltonika AT1200 · Teltonika ATC700 · Teltonika ATC704 · Teltonika ATC774 · Teltonika ATM700 · Teltonika ATM704 · Teltonika ATM774
Questions and answers
Which server and port does the FMB100 use with gTrack?
Server tracker.uplisoft.com, port 11445, TCP / UDP, teltonika protocol.
Can I set the FMB100 by SMS?
Yes. Send "setparam 2001:<APN>;2004:tracker.uplisoft.com;2005:11445;2006:0" to the tracker, with two spaces before it when the SMS login and password are empty, and your APN in place of <APN>.
What data does gTrack read from the FMB100?
248 values: digital inputs, digital outputs, analog inputs, vehicle can data, obd-ii data, bluetooth sensors, 1-wire temperature, fuel level sensors, tachograph, driver identification, driving behaviour, power and battery, gnss and gsm.
Do I need to buy the FMB100 from gTrack?
No. gTrack is tracking software: connect the FMB100 you already have.